Reinforced my gps mount so it doesn’t break as easily.

Switched to ethics props instead of the cheap camo ones and noticed a big difference in vibration.

Also got the light working with a button on the back of my radio.

Hopefully I’ll have some actual on board footage soon I’m waiting on a micro sd card for my go pro.

I am looking for commercial motors in the 60 to 70mm diameter class, 120-200kv. For example the HobbyWing M6215 would work, but it is out of stock. The M6210 is in stock, but slightly undersized for my application. I have never ordered for KDE or other suppliers and I am trying to avoid significant tariffs as well. (USA) Thanks!

2013ish? I think this was the last one sparkfun ran.

Found a weak point on my gps mount and got my filter profile perfected for this frame.

I was having a weird fly away issue which is how I broke the gps mount and my motors were getting hot.

Flys super good now with no weird vibration issues or fly away problems.

I am an EE sophomore, and I want to get into building drones. I have experience with building robots, and I know basic design tools. However, I have no idea where to get started when it comes to drones. I know that there are YouTube videos that help with most of the beginner material, but I want to LEARN this niche.

Hopefully I will have some flight test footage soon

Stay tuned

I have a happy model ep1 elrs receiver and am using a TBS Lucid Pro FC as well as the ESC. My Radiomaster pocket is bound to the receiver but the bars aren't moving in betaflight. Its on serial and its set to crsf as well as aetr1234. Im running firmware 4.5.2 and have out the supafly freestyle preset on the drone. Can someone tell me what im doing wrong. Its my first full build and I'm stuck. I'll probably need more help than just this.

I am working on a project to do with low temperature batteries. I wanted to analyse how suitable some prototype cells would be for an FPV drone pack.

Is there anywhere where people share their flight log data. Specifically I am looking for data of a 10 inch 6s or 8s drone pack power, voltage and current across a flight using the full capacity of a pack.

Hi everyone,
I have been using rapid harness to desing the wiring of a system. Altough the rapid harness software has 95 + million parts from octopart, it looks like a lot of parts are missing. For example any conector from Molex, Hirose and others do not appear. Mostly Deutsch DT Series appear. Has anyone already made some libraries available to share ? Did you made all your needed connectors and parts ?
Thanks in advance for the help.

I'm building my first fpv drone and I noticed that the yellow and white vtx wires aren't in the same order. Is this a problem?

Split deck frame design I created

I haven’t seen too many good things about these motors but it’s all i had enough for in the budget

Please respond soon
One of the screws attached to the motor mount was scraping against the wire and it got cut. This is how much of the wire is left, is it possible for me to solder and repair this?

Hello everyone. I have successfully balanced my drone using the MPU6050 sensor, but I am struggling to maintain altitude using the VL53L1X sensor. I have spent over three consecutive weeks trying to get altitude hold working without success. I would appreciate any help or relevant documentation. Thank you all for reading and for your feedback.

Sensor VL53L1X

https://reddit.com/link/1x47kwi/video/bngzfauii2vh1/player

So I’m planing to buy a Pavo 20 pro 2 but I don’t want to use the o4 pro for my camera. I want to be able to use analog but the frame to mount the camera has 2 holes on each side and the camera I’m going to use (Baby ratel 2) only has one on each side.

How should I make the custom mount?

Is there a better analog camera alternative that matches the screw mounting position of the dji o4 pro?

Betafpv 4 in 1
Happymodel ep1 tcxo
1202.5 11500kv motors
Betafpv c03 camera
Happymodel crown antenna
Cyclone gps
I want to a little long range with it (2-3km)
Open to criticism, I want to make it as good as possible.

Like in the second half of the clip, map segments get stitched together automatically, so you get an endless course that never runs out.

When I had a friend try it out, I found out that older GPUs like the GTX 1660 don't support hardware ray tracing. That's fixed in the version that's up now.

The demo's available now on the store page:

https://store.steampowered.com/app/5197690/Endless_FPV/

I’m building an autonomous quadcopter using a ZD850 frame, PX4 v1.17, a Pixhawk 6x flight controller, and Jetson Orin NX 16 GB. My setup includes a Livox Mid-360 LiDAR, an RGB camera, ROS 2 Humble, GLIM, nvblox, and TensorRT for mapping, odometry, and object detection. I plan to test everything in Gazebo Harmonic with PX4 SITL before moving to real-world flights. Is this setup practical, and what integration challenges or changes would you recommend based on your experience?

My parents grow corn and soybeans, and I’m helping them look into building a couple of spray drones. They know the farming side, so I got assigned motors and ESCs lol.

I want to test one build before ordering parts for the others. A full tank seems like the place to start, but I’m curious how you test it as the tank empties.

Do you run separate tests at full, half-full, and near-empty, or log a whole spraying run? I’m planning to watch current draw and motor temps. Anything else that made you rethink your setup after testing?

If yall built one, I’d appreciate hearing what you missed the first time.