My Model Y got sideswiped on the passenger side (hit-and-run). I went the cheap route with a mobile body guy and the fender came out paint mismatch. Lesson learned. Photo attached.
Looking for a shop in the Bronx, Westchester, or Queens that can redo the fender and repaint so the color and finish match perfectly. It's a lease, so Tesla Approved is preferred. Anyone had good experiences, roughly what did you pay, and how long did it take?

Hello, in July 2025 I inherited my grandfather’s 2005 Honda Accord with less than 90k miles. It had previously been in an accident and received repair 1. Repair 1 failed and it sat and rusted quite a bit. When I received the car my parents got it repaired for me (the quarter panel was not replaced). The repair began to fail in August 2026 and has been getting worse since. I attached photos of the failing now and the original damage. I would love to keep the car cause of the sentimental value and it is in very good mechanical condition.

Is there anything I can do to prevent further damage? Will it take long to be a complete mess in the Northeast?

Thank you, I appreciate any help

My girlfriend side swiped a concrete pole with her newish Mazda CX-5 and I’m looking for advice on the repair. I’m relatively mechanically inclined but haven’t done auto body work (have done brake jobs/struts etc). I fully realize this may be beyond my capabilities, but we’re not necessarily looking to get it perfect.

I’m wondering how others might proceed with this considering the tricky location.

I’m willing to attempt to fix this myself (seems both inner and outer rockers are shot and part of the floor)

The car is really sentimental but I also don’t wanna throw more money at it (buying material to fix it) if it’s a complete lost cause

I was thinking of cutting the pinch welds out and the rockers and welding square steel tubing in its place and then welding sheet metal in place and fabricating my own rockers

im pretty sure someone hit my car in a parking lot a few months ago and this giant dent is super noticeable. I was wondering how i could make it look better. The paint is fine, I can definitely polish it out but i've never delt with a dent before. I should be able to get access to the inside of this door so maybe instead of a dent puller I could hammer it out?

So I've got this rust right on the edge/corner of the roof where it's drops down to make a seat for the windshield. I'm a car guy, not a body guy. But I've mixed a few quarts of bondo over the years. Even tacked a couple quarter panels in. But this, I'm kinda stumped.

Where do I even start? Should I cut it out and replace that small piece of metal? Fiberglass patch? If so, what am I putting behind it? I guess it's the same question for bondo.

My first step is gonna be pulling out that window seal a little, then I was just gonna get to sanding and see where I end up. I'm just looking for a little guidance in the right direction and am very open to any suggestions. Except getting it done professionally. My wallet says that ain't gonna happen. It's a 21 year old work truck. Anyway, thanks!

Oh yeah, it's about 2.5 inches wide for reference

Hello, I was curious if any one had any suggestions on how to fix this tiny dent and paint chip on my car door?

I’m thinking about attempting a diy repair in this order.

1. Gently Pull dent with a glue dent puller tool
   
2. Apply touch up paint pen

Could I potentially just fix the paint chip only and leave the dent? My main goal is to prevent rust.

Any advice is appreciated!

Hey everyone,

I recently noticed a perfectly straight vertical crack in the center section of the rear LED light bar on my 2021 Porsche Panamera (971).

The crack runs from top to bottom, almost exactly in the middle. It's not just a surface scratch either, as I can actually feel it with my fingernail.

What's strange is that I have absolutely no idea how it happened. The car hasn't been in an accident, and there's no visible impact damage or scratches around it. The fact that it's such a straight line makes me wonder if it could be caused by thermal expansion, stress in the plastic, or some kind of manufacturing defect.

The LEDs work perfectly fine, so the damage appears to be limited to the outer plastic lens.

A few questions:

1. Has anyone experienced something similar on a Panamera or another Porsche model?
2. What do you think could have caused this, especially considering how perfectly straight the crack is?
3. Is there any way to repair or seal it properly, or is replacement the only realistic option?
4. Most importantly, can I replace just the outer plastic lens instead of the entire rear light assembly? If anyone knows where to source the plastic separately (AliExpress, eBay, aftermarket suppliers, etc.), I'd really appreciate a link.

I'd hate to replace an otherwise fully functional and expensive light assembly over a crack in the plastic.

I've attached a photo so you can see exactly what I'm talking about.

Any advice or experiences would be appreciated. Thanks!

Hi all!

I just got my Honda CRV-15 front bumper fixed at an auto body shop and noticed this part seems to be off. What do you recommend I should do and is it an easy fix? I’m not sure what could have caused this to happen? Or am I just being paranoid and this is the correct alignment? The car looks great overall and I’m very happy with it.

Thank you!

What’s my best bet to fix this bumper? Trying to avoid a shop and DIY this. Any specific glues, tapes, etc.

The most underrated tools aren't the expensive ones. For car paint diyers, a Dura-Block flexible sanding block. Foam blocks leave waves. This one keeps panels dead flat. $30 and it outperforms gear that costs 10x more.

What's the one tool you bought for one job and now can't live without? Drop it below! the more niche, the better.

Going about replacing my side skirts in my corvette and the previous owner used self tapper screw to secure it but that’s kinda a 1 time deal as the holes are too big to go back in with the same self tapper.

I could go up another size or try to patch the fiberglass and redrill it. I would love to do rivnuts but I’ve heard that can crack or damage fiberglass.

So yeah what should I do? I’ve seen someone recommend plastic rivets as a good solution and I was kinda planning on doing that. The only issue is if I use rivets and I have to drill them out they’ll be lost in the rocker panels forever 😭

Hi all, I’ve never done any body work but I’d like to try tackling these rust spots. Is it a matter of grinding the paint and rust off, filling it, sealing it and then paint/clear coat? I know that’s very high level but it’s potentially my first go at it. Thanks.

I’m attempting to redo clear coat fade for the first time and would like some guidance. The texture before sanding seemed like the base and the clear coat failed. Wiping your hand over it the black would flake right off. I used 400 on a sander and that seemed to smooth things out but there’s still this dry skin like texture close up in the last pic. Even though its not flaking anymore I was wondering if I should cut through it more? I avoided the seemingly good paint in the center. I’m using single stage paint.

So I've welded in a few patch panels, primed everything with 2K brush on epoxy primer, put some polyurethane 1K seam sealer over the welds. I was thinking of putting another coat of 2K epoxy primer over everything for another layer of protection, but I got to thinking, is there actually any benefit of covering the seam sealer itself with the primer? These are all concealed areas so the appearance doesn't matter at all

In my mind, putting epoxy primer over the seam sealer just leads to a cracking risk doesn't it? Would it be better to try to avoid the seam sealer and just put another coat over the surrounding surfaces? Or just send it and prime everything?

It’s not super thick but I don’t like how it looks, thanks in advance

I’ve never been much of a cat person, nor have I had much assistance from family. I bought my first car from my friend when they wanted a new one and have an MOT that runs out in December. I was just slowing down onto a junction when this electric bike came off the junction and tore into the lower side skirt (as google refers to it) off my car. I’m halfway home so figure I could try some glue I’ve got in my car (which I now realise was stupid) and now I’m home I don’t know what to do. I don’t have a local mechanic, or even know if this would be a job for them as it appears to be somewhat cosmetic? Is this something I can fix myself. My knowledge is very limited to changing a tire and a battery. Is it something a YouTube video and the proper equipment can fix or should I find a mechanic?

Also, I do realize once I get done sanding, I need to enclose this to kind of resemble a paint booth.

My car had the passenger side fender changed, along with the front bumper and a headlight, and my hood was repainted. Is this acceptable? My left fender which wasn’t changed is now more out of place than the new one, or am just too picky? Thankfully I had a dash cam otherwise I would have been on my own.

Accidentally reversed in a parking garage with the door open and hit the edge... There is a small hole. How would you touch this up and rust protect without doing a full repair?

Hi guys i’m fixing up my accord today after collecting parts for a bit. I have a brand new headlight assembly, fender@bumper from the junkyard, also got a used headlight support bracket and a couple others since obviously it’s bent. looking at the pictures, am i okay to put the new bumper fender and headlight on, how does the radiator look and supports and what not. also, that lining i’m holding in one of the pictures, should i just cut it off? Any advice it’s appreciated. Trying to do it today as I still use it. Thank you guys

Guess who: bracket edition. 2015 Honda odyssey. Looked in fender inner structure and rad support. How could a simple bolt on bracket not be replaceable? No part # on it. Maybe I’m blind or dumb but I can’t find this to save my life. I would’ve had an easier time just grabbing one from a junk yard. Surely someone else has run into this issue and found the right one?

Hello,

Have a paint question.

Shop is using Diamont Solvent, and lately on certain colors it seems to have a black hazy look thats stopping the color from popping. Like the color is there but its been dusted with black making it too dark.

Mostly happens on dark metallic especially blue, and happens on both rubber and metal. The painter seems to think the formulas have too much black tint in them

Anyone come across this, and have any idea what's happening?

Thanks

Before we start, insurance wants to total it. I want to keep the car 😮‍💨

Just looking for advice. If anyone has repaired damage this bad? Tips to solve in steps? Could I get someone to pull this dent out first, then maybe get someone later to do whatever step is needed next. Or any temp way to fix or cover damage?

The car is a 2019 Genesis G70, it’s drivable, sensors are still working, and low mileage so I plan to get some more good years out of her. Thanks in advance.